A popular way to give a room character and beauty is to install tongue and groove panels over drywall. While there are many ways to install this type, each method requires precise cutting and careful measuring. Most panels are attached to furring strips which run vertically along the wall. This is the most popular method. Another option is to install diagonally. To create the long groove side, a 45-degree angle was used at both ends of each panel.
Installation Steps
You must remove all hooks, outlets and nails from walls before hanging wood planks. You will also need to sand the walls for any protrusions. You can use a power sander or large sandpaper sections and an extension base to accomplish this task.
Check whether the tongue and groove paneling has been nailed to drywall, studs or both
A pry bar can be placed near the corner of the wall where the tongue and groove panels meet. With your hammer, tap the prybar into a seam where the two walls meet. If the panel is nailed to drywall, you'll need to pull the panel away from the wall, using a pry bar and pliers.
You should determine whether your tongue & groove wall panels were nailed, glued or both
Once you are certain your paneling and drywall are nailed, start removing trim. It's possible to reuse trim in the best case scenario, so make sure you don't damage it.
If you are unable or unwilling to reuse the trim you will need to order new wood paneling. You will need four sheets of 4'x8" wood paneling to cover the walls you want. Measure the wall width and divide that number by 4. If you have walls greater than 8 feet tall, subtract one panel for each door and one panel for each window.
Drywall Straightedges
Make sure your wood paneling runs evenly along the drywall surface. Run a straight edge down the wall side-to-side to make sure it is. Be aware of any areas where the wall is higher than or lower than the wood paneling. Your paneling will not be flat if the drywall bulges.
Sand the Drywall With a Dust Mask
Sand down the areas of drywall that protrude when you install tongue and groove paneling. This will allow your paneling to be installed more easily and evenly.
Finishing with Wood Putty
After you've sanded down the drywall, apply a coat of wood putty to the walls and the paneling to seal the joints between the walls and the paneling. To give the paneling a natural look, you can stain it with a wood stain. However, this takes more work than painting.
Drywall Installation: Attaching Paneling
A nail set with rounded heads is required to attach wood panels to drywall. These fasteners are available at most hardware stores and cost about $4 per pack of 16-penny common nails. They can be used on any type of wood such as plywood or drywall. However, they are not recommended for use with thicker boards.
FAQ
What should I look for when buying a home?
Before purchasing a new home, make sure that you have enough money saved up to cover closing costs. You may want to refinance your mortgage if there isn't enough cash.
What room should first be renovated?
The heart of any house is the kitchen. It is where you spend your most time cooking, entertaining, eating, and relaxing. If you're looking to make your kitchen more functional, attractive and beautiful, this is the place for you!
Bathrooms are an important part any home. The bathroom provides privacy and comfort while you do everyday chores like brushing your teeth, shaving and bathing. These rooms can be made more functional and attractive by installing storage space, a shower, or replacing older fixtures with newer models.
How many times do I need to change my furnace filter?
The answer will depend on how often your family is going to use your heating system. It is worth changing your filter more often if you intend to spend a lot of time outside during winter months. If you're not often out of your home, however, you may be more able to wait for the filter to change.
A typical furnace filter lasts approximately three months. This means that your furnace filters should be changed every three to four months.
For information on when to replace your filter, you can consult the manufacturer. Some manufacturers recommend that you replace your filter after every heating season. Others suggest waiting until there are visible dirt deposits.
How important it is to be pre-approved for loans?
It's important to be pre-approved for mortgages. This will allow you to determine how much money you can borrow. It helps you to determine if your loan application is eligible.
Should I hire an architect or builder?
It might be easier to have someone else do the work if you're planning on renovating your own house. But if your goal is to buy a house, hiring an architect/builder will ensure that you get the home you desire.
How can you renovate your house without spending a lot of money?
When renovating a home without spending money, the following steps should be followed:
-
Create a budget plan
-
Find out the materials you require
-
Decide where you want to put them
-
You will need to make a list of the things that you must buy.
-
Calculate how much money is available
-
Plan your renovation project
-
Start to work on your plans
-
Do your research online
-
Ask your family and friends for assistance
-
Be creative!
Is it better to finish floors or walls first?
It's important to know what you want to accomplish before you start any project. It is crucial to plan how you'll use the space, what people will use it for, and why. This will help you decide if you should go for flooring or wall coverings.
You might choose to first install flooring if your goal is to create an open concept kitchen/living area. Wall coverings are an option if you prefer to keep this space private.
Statistics
- A final payment of, say, 5% to 10% will be due when the space is livable and usable (your contract probably will say "substantial completion"). (kiplinger.com)
- Most lenders will lend you up to 75% or 80% of the appraised value of your home, but some will go higher. (kiplinger.com)
- It is advisable, however, to have a contingency of 10–20 per cent to allow for the unexpected expenses that can arise when renovating older homes. (realhomes.com)
- They'll usually lend up to 90% of your home's "as-completed" value, but no more than $424,100 in most locales or $636,150 in high-cost areas. (kiplinger.com)
- According to the National Association of the Remodeling Industry's 2019 remodeling impact report , realtors estimate that homeowners can recover 59% of the cost of a complete kitchen renovation if they sell their home. (bhg.com)
External Links
How To
Do you prefer renovating exterior or interior?
Which one should I first do?
When choosing which project to begin with, there are many things to take into consideration. The most common factor is whether the building is old or new. The condition of the roof, windows and doors, flooring, wiring, and other aspects are all important. When the building is new, there are many things to consider such as its location, size, number, style, and so forth.
The roof is the most important thing to inspect if the building is older. If it looks like the roof could collapse any minute now, you may want to start on the renovation. The roof should be in good shape before you move on to the next stage. Next, inspect the windows. You might need to replace them if they are damaged or stained. Next, check the doors for debris and clean them up. Then, if everything seems okay, you can begin working on the floors. Make sure that the flooring is solid and sturdy so that no matter how hard you walk on it, nothing breaks. Now you can start to add the walls. Check the walls for cracks and damage. If the wall is in good condition, you can move on to the next step. You can now inspect the ceiling. Check the ceiling and make sure that it is strong enough to hold up whatever weight you decide to put on it. Then you can start your renovations if all goes well.
You would want to begin with the exterior if the building was recently built. Examine the exterior of the house. Is it clean? Are there cracks or holes? Does it look good? If your exterior isn't looking great, you should make some changes. It is not a good idea to make your home look unattractive. Next, inspect the foundation. You should repair any foundation that appears weak. You should also inspect the driveway. You want it to be smooth and flat. It should be smooth and flat. If it isn’t, you need to fix it. You should also inspect the sidewalk while you're checking your driveway. It should be replaced if it is uneven.
Once these areas are checked, you should move on to the inside of the house. Begin by inspecting the kitchen. Is it clean and well-maintained? If it is messy, then you should probably clean it up. Next, you should inspect the appliances. You want them to be in good order and working correctly. If they aren't, then you should either buy new ones or fix them. You can then inspect the cabinets. Paint them if they're stained or scratched. If they are in great condition, then you can go to the bathroom. You should inspect the toilet here. If it leaks, it is time to get a new one. It's best to wash it if it's only dirty. Next, check out all the fixtures. Make sure that they are clean. They should be cleaned if they are dirty. Finally, make sure to inspect the countertops. Repainting countertops is advisable if they have cracked or are chipped. You should seal them if they are shiny and smooth.
Last, check the furniture. Verify that everything is in good condition. You should find what is missing if it is not there. If something is broken, then you should probably repair it. After you've checked everything, it is possible to move outside and complete the job.